The Ride-Out Checklist: 5 Aerial Fiber Problems Worth Stopping the Truck For

aerial fiber inspection

What I Still Stop the Truck For

I still stop the truck.

I started as a ground hand in the late 1970s, hooking poles, and I never learned how to drive past a span without looking up. Most of what I stop for is not a mystery. It is five conditions. Each one is visible from the driver’s seat, and each one already has a specification. A crew can meet it. A supervisor can see from the road whether they did.

This is the ride-out I still use

The closure is in the grass

A splice case belongs on the strand, lashed, sealed, with the slack dressed beside it. I stop for the case on the ground, or hanging from the cable, with the storage loops piled in the ditch. Sometimes the grass has grown through the coil. That is not a recent repair. That is the plant.

The slack should be long enough to lower the closure, work it, and put it back. Corning’s lashed-aerial procedure tells the crew to leave enough cable at the splice to reach the ground and into the splice vehicle, plus another 16 feet, and then it says the quiet part out loud: do not coil the cable on the pole. Lash the closure and the slack to the messenger. If you use snowshoes, they must be sized to protect the bend radius. The slack is a tool. It is not the installation.

The closure itself is built for a specific place. Telcordia GR-771-CORE sets the generic requirements for a fiber splice closure in the outside plant: sealing, mechanical strength, and the environment in which the closure was tested. An aerial closure sitting in standing water or under a mower wheel is not in that environment. Inside the case, the fiber has a bend limit. Verizon’s purchasing spec, written against GR-771, requires a 30 mm bend radius for fiber and 38 mm for buffer tubes in the applications they call out, and never tighter than the cable maker’s own number. A loop stomped into the dirt misses both.

OFS wants the slack stored next to the aerial closure, in coils or a snowshoe, and wants spare fiber inside the case so a storm load can move the fiber without pulling the splice. Their guide calls for at least five coils on many cables and a minimum coil diameter of 18 inches on many designs with 216 fibers or fewer. The exact diameter is on the cable sheet. The principle is not. If the coil is small enough to kink, the light may pass in April and fail in August, when the cable is hot and the bend loss shows up.

If I can see the case from the truck, and it is not on the strand, I stop

The lashing let go

The cable and strand are one assembly, and the lashing wire holds them together. When the lashing breaks, the cable sags on its own. That belly is the low point of the span, exactly where a truck, a boat trailer, or a neutral conductor will find it.

The termination is where a lot of this starts. Corning’s procedure places the lashing-wire clamp about 16 inches from the pole centerline, or farther out if the bend radius requires it, and it requires three wraps of lashing wire around the strand before the clamp takes the wire. Those wraps prevent the wire from kinking and breaking at the termination. Skip them, and the span fails at the pole, the first place a ride-out should look.

One lashing wire is not the answer on every span. Corning double-lashes where vibration and stress call for it. CommScope’s construction manual is plainer: double-lash two or more cables, trunk cable, and street and railroad crossings. A single broken wire at a road crossing isn’t cosmetic. It is the cable leaving the strand over the place a vehicle is tallest.

The same wire has a safety side. OSHA’s telecommunications standard, 29 CFR 1910.268, says the strand has to be tested and shown strong enough before anyone hangs a splicing platform and a person on it. A span with the lashing gone and the cable in a belly isn’t a strand you trust with a platform. The ride-out that stops for broken lashing is doing the public and the crew the same favor.

The clearance left with the lashing

Clearance is a number, measured at the worst sag, not on the morning the crew felt good about it.

In the 2023 National Electrical Safety Code, Table 232-1 sets the vertical clearance for insulated communication cable. Over roads, streets, and other surfaces subject to truck traffic, the base number is 15.5 feet, at the largest sag. Driveways and lots that trucks actually use sit on that same row. Footnotes cover a residential service drop and ground that only a pedestrian will ever cross. A trunk or a feeder sagging over a public road is not in those footnotes.

“Largest sag” is the part people skip. The table is not the clearance on build day. It is the clearance after the span reaches the sag condition the code tells you to design for. A span that clears a box truck in January can be illegal in August, and it can still be the same cable on the Gulf Coast, not a theoretical season. August is a season.

The other gap is the one above the cable. Between a power neutral and a communication messenger, the NESC does allow the midspan clearance to tighten. IEEE interpretation IR571 walks through the exception: about 12 inches in the span, and only when the neutral meets Rule 230E1, the neutral is bonded to the messenger on the schedule in Rule 92C, and the clearance at the pole is still held (the interpretation uses 30 inches at the support for that exception). Sag spends that margin from the middle of the span. Broken lashing is how you spend it. The cable drops out of the communication space and into whatever is using the road.

I do not carry a measuring wheel in the cup holder. I carry the picture of a 15-foot truck. If I would not drive a moving van under the low point, I stop.

The loop is doing a job it was never given

Slack has two jobs. It lets the next tech get the closure to the ground and into the truck, and it holds a bend the fiber can live with for decades. A loop wrapped around a pole, a loop the size of a dinner plate, or a loop lying in the ditch is doing a third job nobody specified.

Corning again: do not coil the cable on the pole. Put the loop where the snowshoe or the strand-mounted coil keeps the diameter, and keep the closure where a splicing vehicle can actually stand. OFS stores that slack adjacent to the closure for the same reason. The length is local. The shape is not. If the loop is tighter than the cable sheet, the sheet wins, and the argument is over.

The same loop is what makes the closure maintainable. If the slack will not reach a safe place to work, the next tech splices it where it hangs, or lowers it and leaves it. That is how a case ends up in the grass with the storage still attached. The ride-out question is simple. Can this closure come down, get worked, and go back up without the fiber paying for it?

Temporary became the design

Every storm and every cut produces temporary plant. That is honest work. The failure is leaving it.

Rule 014 of the NESC waives emergency and temporary installations, and it is worth reading next to Rule 230A. An emergency installation can operate with a clearance that the permanent plant would not allow, and the code tells the operator to remove, replace, or relocate it as soon as practical. A temporary overhead installation is narrower. Strength can be eased, down to Grade N. Clearance does not get the same pass. The McGraw-Hill NESC handbook draws that distinction in one diagram: emergency work may decrease the Section 23 clearances and then has to come out; temporary overhead work does not get a shorter road.

The code also refuses to define how long “temporary” may last. The field has filled that in. If the drop is lashed with tape, if the coil is figure-eighted in a bush, if the slack has been on the ground long enough to take a set, it is not temporary anymore. It is the design, and it owes the road the permanent clearance.

I stop for those because they outlive the ticket that created them.

  The Check List

Five things. All of them visible without a bucket.

  1. The closure is on the strand, sealed, with the slack dressed beside it. It is not in the grass.
  2. The lashing is intact and terminated at the pole, with the wraps the procedure calls for. Crossings, trunk, and any strand with two cables are double-lashed.
  3. The storage loop matches the cable sheet, and there is enough to reach the ground and into the truck.
  4. The low point of the span still clears 15.5 feet over a road trucks use, at the worst sag, and the gap to the neutral is still the gap the attachment was built for.
  5. Nothing called temporary has been up long enough to become the plant.

If you run construction, hand that list to the person who rides the job. If they already stop for these, the plant is being looked at. If they drive past them, the span will bring it up later. Usually in August. Usually at the lowest point.

Jim Cox is Managing Partner of OSP Technologies in Conroe, Texas. He started as a ground hand and has spent more than forty years in outside-plant construction, engineering, and operations.

Sources

  1. IEEE, National Electrical Safety Code, ANSI C2-2023. Rule 014 (waiver for emergency and temporary installations), Rule 230A, Rule 232 and Table 232-1 (vertical clearance of communication cables; 15.5 ft over roads and surfaces subject to truck traffic, at largest sag), Rule 235C (clearances between wires on different supporting structures).
  2. IEEE Standards Association, Interpretation Request IR571, Rule 235C2b, midspan clearance between a supply neutral and a communication messenger.
  3. IEEE Standards Association, Interpretation Request IR598 (13 March 2023), Rule 014C, temporary installations and construction grade in the 2023 edition.
  4. McGraw-Hill, National Electrical Safety Code (NESC) Handbook, 2017 edition, discussion of Rule 014: emergency installations may reduce Section 23 clearances and must be removed, replaced, or relocated as soon as practical; temporary overhead installations are not granted that clearance reduction.
  5. Telcordia, GR-771-CORE, Issue 2, Generic Requirements for Fiber Optic Splice Closures.
    Verizon, VZ-TPR-9412, fiber splice closure requirements based on GR-771-CORE, including bend radius (30 mm fiber, 38 mm buffer tube, or the manufacturer limit if tighter control is required) and slack storage.
  6. Corning Optical Communications, SRP-005-010, Lashed Aerial Installation of Fiber Optic Cable, and SRP-005-048, FlexNAP System Cable Assembly Placing — Lashed Aerial. Lashing-wire termination, double lashing, slack to the ground plus 16 ft (5 m), and the prohibition on coiling cable on the pole.
  7. OFS, IP-003, Aerial Installation Guidelines for Fiber Optic Cable. Slack coils adjacent to the closure, coil diameter, spare fiber inside the case, and strand loading under NESC conditions.
    CommScope, Broadband Applications & Construction Manual. Double lashing for two or more cables, trunk cable, and street and railroad crossings.
  8. OSHA, 29 CFR 1910.268, Telecommunications. Strand strength before hanging a splicing platform.

Frequently Asked Questions

Look for five things you can see from the truck: closures off the strand; broken or poorly terminated lashing; slack loops coiled too tightly or left on the ground; spans sagging below the required clearance; and “temporary” repairs that were never made permanent.
Lash it to the strand and seal it, with the slack stored neatly beside it in coils or snowshoes. A closure lying in the grass or hanging loose from the cable is outside the conditions it was designed and tested for under Telcordia GR-771-CORE.
Corning’s procedure calls for enough cable to reach the ground and into the splice vehicle, plus another 16 feet (5 m). The slack should be lashed to the messenger, not coiled on the pole.
Verizon’s spec, which is based on GR-771, requires a 30 mm bend radius for fiber and 38 mm for buffer tubes. If the cable maker’s limit is stricter, follow it. Coils that are too tight can pass testing in spring and then fail in summer heat.
Lashing holds the cable to the strand. When it breaks, the cable sags, and the low point of the span becomes something a truck, trailer, or power neutral can hit. Road and railroad crossings, trunk cable, and strands carrying two or more cables should be double-lashed.
Under the 2023 NESC, Table 232-1, insulated communication cable must clear 15.5 feet over roads and other truck-used surfaces. That’s measured at the largest sag, so the hot summer condition counts, not the clearance on the day it was built.
The NESC doesn’t set a time limit, but emergency installations must be removed, replaced, or relocated as soon as practical. Temporary overhead installations don’t get reduced clearances. If a repair has been up long enough to settle in, treat it as permanent plant.
Not until it’s been checked. OSHA 29 CFR 1910.268 requires that the strand be tested and shown to be strong enough before a splicing platform and a worker are hung on it. A span with broken lashing and a sagging cable doesn’t pass that check.

Share:

More Posts

AI Infrastructure Design

AI Infrastructure Design

Building Networks That Perform Under Pressure Fiber Count Alone Is Not a Strategy For decades, service providers competed on one primary metric: fiber count and

Send Us A Message